Following are the instructions included with every set of Original Keith Tuners:

HOW TO INSTALL AND SET YOUR KEITH BANJO TUNERS

TO INSTALL:

1. Remove the 2nd and 3rd strings and tuning pegs from your banjo. Then compare your two Keith Tuners.
and you'll notice that the spools on which the strings wind are of different sizes.

2. The Keith Tuner with the larger spool is for the second string. Remove the nut and washer and insert it
through the headstock. positioning it so that the two side thumbscrews can be conveniently reached while
tuning. Put the flat washer and the nut back on, and tighten securely.

3. Similarly, install the Keith Tuner with the smaller spool for the third string.

* PLEASE NOTE: When tightening down the nuts, use a smooth-jawed adjustable wrench. Pliers will scar
the metal, and may slip off and damage the headstock. If the holes in your banjo's headstock are too small
for the Keith Tuners, we recommend having them drilled out by a qualified instrument repairman.

TO SET THE STOPS:

1. Loosen all four side thumbscrews one-half a turn. The Keith Tuners will operate like standard tuning pegs.
Now put on the second and third strings.

2. Tune the banjo to the open G tuning (second string - B. third string - G). Firmly tighten the black side
thumbscrews, which will set the high stops. Now, tune the second string down to A and the third string
down to F# (put the banjo into open D tuning) and firmly tighten the uncolored side thumbscrews. This will I
set the low stops. The tuners will now operate as "D-tuners". and will not turn past the high or low stops.

3. If the pearlescent buttons are not at a convenient angle to turn while playing, simply unscrew the end
thumbscrew that holds the button in place and pull the button free of the shaft. Since the button will fit on
the shaft in six different positions, you can install it at the angle that suits you best. Push it back on the
shaft and screw in the end thumbscrew.

* NOTE: These directions assume that the strings are wound on the spools in the normal manner; that is, the
pitch of the second string is raised by turning its tuner counterclockwise, and the pitch of the third string is
raised by turning its tuner clockwise. If you prefer to wind one or both of your strings in the opposite
direction, just swap the black and uncolored thumbscrews on the appropriate tuner.

A FEW IMPORTANT POINTS:

* When setting the stops, always tune up to the high note and down to the low note. Set the high stops with
both strings raised, and the low stops with both strings lowered.

* Other tunings may be used besides the one described. Just remember that the stop for the higher note is
set with the black thumbscrew.

* If the high note seems to come up a little flat, check to see if the string is binding in the nut or the bridge. It
may be necessary to reshape the string groove, using a small knife or file. so that the string slides freely in
it. It may also help to shave a little pencil lead into the grooves of the nut for lubrication.

* If the tuners have a tendency to slip when both stops are set, tighten the end thumbscrew which holds the
button in place and which also adjusts the friction.

* A little grease may ooze from the tuners, particularly when they are new. This is not a sign of trouble — they
are packed with grease at the factory, and it is normal that some will work its way out. Just wipe it off.

* Don't force the tuners past the stops. This could result in internal damage. Tighten the side thumbscrews
firmly (by hand - don't use pliers) to prevent the stops from slipping.

* Don't attempt to take the tuners apart. The guarantee is void if they have been abused or disassembled.

* If this pair of tuners is for the first and fourth strings, they will both have large spools, and will be labeled
"1st" and "4th".

* After several years of use, the grease may begin to dry out and the tuners become hard to turn. This can be
corrected by removing the side thumbscrews and adding a little light oil such as 3-in-1 oil, sewing machine
oil, or penetrating oil. Remember: these tuners are precision-made, and require lubrication. If you
continue to use them when they are dry and hard to turn, you may cause internal damage. Before serious
problems develop, send them back to us for a complete cleaning and relubrication. There is a nominal
charge for this service.

* Don't forget to fill out your guarantee card and mail it in.

LIFETIME GUARANTEE

These Keith Banjo Tuners are guaranteed by Beacon Banjo Company, Inc. without time limit
to the original owner against defects in materials or workmanship. We will repair or replace
(at our option) any faulty Keith Banjo Tuner, provided that it has not been abused
or disassembled. No other warranty is expressed or implied.

BEACON BANJO Co., Inc. P.O. Box 597 Woodstock. NY 12498 tel:(914) 679-8314 Copyright©2002 Beacon Banjo

To learn how to tune your new Keith Tuners, click here.

Here's what they look like on your banjo after installation.

Click on images for magnified view:

Be sure to write if you have any questions regarding these lessons:

Banjo Website Map

---